PIC16F737-I/SP【PDF 162/231 页】IC PIC MCU FLASH 4KX14 28DIP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3841

158页 159页 160页 161页 [162页]163页 164页 165页 166页

PIC18F2X1X/4X1X

DS39636D-page 250

2009 Microchip Technology Inc.

22.3

Two-Speed Start-up

The Two-Speed Start-up feature helps to minimize the

latency period from oscillator start-up to code execution

by allowing the microcontroller to use the INTOSC

oscillator as a clock source until the primary clock

source is available. It is enabled by setting the IESO

Configuration bit.

Two-Speed Start-up should be enabled only if the

Primary Oscillator mode is LP, XT, HS or HSPLL

(Crystal-Based modes). Other sources do not require

an OST start-up delay; for these, Two-Speed Start-up

should be disabled.

When enabled, Resets and wake-ups from Sleep mode

cause the device to configure itself to run from the

internal oscillator block as the clock source, following

the time-out of the Power-up Timer after a Power-on

Reset is enabled. This allows almost immediate code

execution while the primary oscillator starts and the

OST is running. Once the OST times out, the device

automatically switches to PRI_RUN mode.

To use a higher clock speed on wake-up, the INTOSC

or postscaler clock sources can be selected to provide

a higher clock speed by setting bits IRCF2:IRCF0

immediately after Reset. For wake-ups from Sleep, the

INTOSC or postscaler clock sources can be selected

by setting the IRCF2:IRCF0 bits prior to entering Sleep

mode.

In all other power-managed modes, Two-Speed Start-

up is not used. The device will be clocked by the

currently selected clock source until the primary clock

source becomes available. The setting of the IESO bit

is ignored.

22.3.1

SPECIAL CONSIDERATIONS FOR

USING TWO-SPEED START-UP

While using the INTOSC oscillator in Two-Speed Start-

up, the device still obeys the normal command

sequences for entering power-managed modes,

including

multiple

SLEEP

instructions

(refer

Section 3.1.4 “Multiple Sleep Commands”). In

practice, this means that user code can change the

SCS1:SCS0 bit settings or issue SLEEP instructions

before the OST times out. This would allow an

application to briefly wake-up, perform routine

“housekeeping” tasks and return to Sleep before the

device starts to operate from the primary oscillator.

User code can also check if the primary clock source is

currently providing the device clocking by checking the

status of the OSTS bit (OSCCON<3>). If the bit is set,

the primary oscillator is providing the clock. Otherwise,

the internal oscillator block is providing the clock during

wake-up from Reset or Sleep mode.

FIGURE 22-2:

TIMING TRANSITION FOR TWO-SPEED START-UP (INTOSC TO HSPLL)

Q3 Q4

OSC1

Peripheral

Program

PC + 2

INTOSC

PLL Clock

PC + 6

Output

CPU Clock

PC + 4

Clock

Counter

Note 1: TOST = 1024 TOSC; TPLL = 2 ms (approx). These intervals are not shown to scale.

2: Clock transition typically occurs within 2-4 TOSC.

Wake from Interrupt Event

TPLL(1)

n-1 n

Clock

OSTS bit Set

Transition(2)

Multiplexer

TOST(1)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式